add automotive carpet site in SUNOL add automotive carpet site SUNOL

add automotive carpet site in SUNOL

add automotive carpet site SUNOL

add automotive carpet site in SUNOL.Many people find it more cost efficient to replace their auto carpet, instead of trying to clean the dirt or smell from a soiled auto carpet.
Buying this form of automotive carpet will make the job much easier and will eliminate most of the work.
It is important to note that there are 2 types of automotive carpet backing.
It is a heavy foamlike rubber that is usually black.
This type if backing is added to improve heat and sound insulation as well as some padding under the carpet.
Some aftermarket carpet retail stores will sell you the same carpet with either type of backing.
The first thing you will need to do when replacing your auto carpet, is to purchase a carpet kit for your particular vehicle.
It is important to point out that now would also be a good time to buy a matching set of floor mats from the same retail store where you buy your carpet.
Most manufacturers cut your molded carpet and floor mats from the same roll of carpet and to ensure that you get the same exact die lot; you should order both at the same time.
Be sure to pull the new auto carpet out of the box as soon as it arrives, since it will be rolled up and crammed into the box.
Sometimes, letting it sit in a warm room, or direct sunlight will help speed up this process.
Once the carpet has relaxed, you can begin the job of installing the new auto carpet.
The first step will be to remove the existing carpet from the vehicle.
You may need to remove the sill plates by the doors, the seats and seat tracks if they are holding down the auto carpet and the center console.
Basically, anything that is holding down the carpet will need to be removed in order to get the carpet out.
Be careful not to destroy the existing carpet, and certainly do not throw the carpet away or discard it, as you will need to use it in a few minutes.
Just set the carpet aside for the time being.
Now you should do a little prep work on the floor of your car to get ready to install the new carpet.
At this time you can remove the old carpet padding, if any was left behind, but be sure not to remove any body insulation from the floor.
You can install heat or sound insulation such as dynamat at this time and patch or repair any holes in the floor of the vehicle.
And it should go without saying, but sweep and clean up and dirt or loose matter from the floor of the vehicle.
Most aftermarket auto carpet kits will come slightly oversized and without the precut holes.
So, there will be a little work to get the new carpet into the car.
There are 2 methods of cutting and trimming your carpet to get it into the vehicle; you can choose which will work best for you.
Your first option is to place the new auto carpet over your old carpet, trim the edges and cut the holes.
If you chose this option, you will need to be very careful not to over cut the holes or cut too much from the edges, since you are using the old carpet instead of the vehicle itself.
The 2nd option is to work the new carpet into the contours of the vehicle floor and trim the carpet as you go.
This method will give you more accurate results, but may be a little more difficult.
Either way, it is important not to cut and trim too much with any one cut.
It is best to work slowly, making small cuts and double check that the carpet has not shifted after each cut.
You can then simply push the bolt through the carpet.
There is usually no need to try to cut a complete hole in your new carpet.
Occasionally you will find that a small section of the auto carpet wants to lift up off the floor, or tries to create a small wrinkle.
This can easily be fixed with a small shot of spray adhesive.
It is not recommended to spray the entire floor of the car, since the molded carpet should be held in place with the seats and trim pieces that were holding the original carpet in place.
Once the auto carpet is in place, and trimmed to fit, now you can begin to replace the pieces that were holding the original carpet in place.
If you removed the seats, sill plates and trim pieces, then all of these pieces will need to go back into the vehicle.
Once all of pieces are back in place, your job is complete.
You will be amazed at how much difference a little work can make to the appearance of your vehicle, not to mention removing that horrible smell that some things like milk can leave behind!
add automotive carpet site in JOSEPHINE add automotive carpet site
JOSEPHINE